DOW Universal Support Material from taulman3D on Vimeo. |
|
evolv3d_usm_sds.pdf | |
File Size: | 210 kb |
File Type: |
evolv3d_tm__usm_tds.pdf | |
File Size: | 220 kb |
File Type: |
EVOLV3D™ USM Universal Support Material
Introduction EVOLV3D™ USM overcomes limitations of other support materials through its compatibility with
a broad array of popular build materials, a broader print temperature range, easy removal
through tap water dissolution at room temperature, and safer disposal of the solution. These
features significantly increase the design space for additive manufacturing innovators to build
complex and functional parts with an array of materials that may have previously been
impossible. 3D printing is often done outside of industrial settings (homes and offices) by users
who may not have chemical handling training. As a non-hazardous material that does not use
harsh reagents or generate harmful waste, EVOLV3D USM reduces handling concerns and
meets environmental requirements.
Application
Support material for 3D printing Sustainable
For slicer settings of Density, use 0.84
Features
Universal - Works with a broad array of popular build materials
Cost-efficient - No need to stock multiple support materials
Easy to remove - Dissolves in tap water at room temperature
Safer to handle - No harsh chemicals needed for clean-up
Can be washed down the drain
Print Head Temperature Range 200°C to 250 °C
Bed Temperature 20 °C to 70 °C
Storage and
Handling
EVOLV3D™ Universal Support Material (USM) has a high affinity to water, allowing it to easily
dissolve in tap water after printing. However, this also means the filament is susceptible to
moisture when stored. Below are some best practices to help maintain the product’s
performance over its lifetime.
Store EVOLV3D USM Filament in Moisture-Free Containers
In high-humidity environments, EVOLV3D USM may pick up moisture from the air, which can
cause issues during the printing process. The filament comes with moisture-barrier packaging to
prevent this during transportation. Once the package is opened, store EVOLV3D USM spools in
air-tight containers with multiple desiccant packets to maintain a low-humidity environment.
Drying EVOLV3D USM Filament Before Printing
When EVOLV3D USM has been exposed to high humidity, drying it before printing is
recommended. The filament can be dried at room temperature in approximately six (6) hours.
This is done by placing it in an airtight container along with multiple desiccant packets. For faster
drying, place the EVOLV3D USM in an airtight container with multiple desiccant packets and
place the container in an oven. Heat the filament to 50°C. This reduces drying time to
approximately two (2) hours.
Continuous Feed-Dry Devices
For best results, a continuous feed-dry device is recommended when using EVOLV3D USM to
help keep the filament dry during the printing process.
Introduction EVOLV3D™ USM overcomes limitations of other support materials through its compatibility with
a broad array of popular build materials, a broader print temperature range, easy removal
through tap water dissolution at room temperature, and safer disposal of the solution. These
features significantly increase the design space for additive manufacturing innovators to build
complex and functional parts with an array of materials that may have previously been
impossible. 3D printing is often done outside of industrial settings (homes and offices) by users
who may not have chemical handling training. As a non-hazardous material that does not use
harsh reagents or generate harmful waste, EVOLV3D USM reduces handling concerns and
meets environmental requirements.
Application
Support material for 3D printing Sustainable
For slicer settings of Density, use 0.84
Features
Universal - Works with a broad array of popular build materials
Cost-efficient - No need to stock multiple support materials
Easy to remove - Dissolves in tap water at room temperature
Safer to handle - No harsh chemicals needed for clean-up
Can be washed down the drain
Print Head Temperature Range 200°C to 250 °C
Bed Temperature 20 °C to 70 °C
Storage and
Handling
EVOLV3D™ Universal Support Material (USM) has a high affinity to water, allowing it to easily
dissolve in tap water after printing. However, this also means the filament is susceptible to
moisture when stored. Below are some best practices to help maintain the product’s
performance over its lifetime.
Store EVOLV3D USM Filament in Moisture-Free Containers
In high-humidity environments, EVOLV3D USM may pick up moisture from the air, which can
cause issues during the printing process. The filament comes with moisture-barrier packaging to
prevent this during transportation. Once the package is opened, store EVOLV3D USM spools in
air-tight containers with multiple desiccant packets to maintain a low-humidity environment.
Drying EVOLV3D USM Filament Before Printing
When EVOLV3D USM has been exposed to high humidity, drying it before printing is
recommended. The filament can be dried at room temperature in approximately six (6) hours.
This is done by placing it in an airtight container along with multiple desiccant packets. For faster
drying, place the EVOLV3D USM in an airtight container with multiple desiccant packets and
place the container in an oven. Heat the filament to 50°C. This reduces drying time to
approximately two (2) hours.
Continuous Feed-Dry Devices
For best results, a continuous feed-dry device is recommended when using EVOLV3D USM to
help keep the filament dry during the printing process.